Service Manual 04/2010 Rev.B
83
Fig.157
TO REPLACE THE FLANGE:
Remove the small and big flange O rings.
Remove the screw #1 and the washer
(Fig.158).
Fig.158
Remove the manifold #2 (Fig 158) from the
flange (Fig.159).
Fig.159
IMPORTANT!
IN CASE OF FLANGE REPLACEMENT IT IS
SUGGESTED THE REPLACEMENT FO THE
MANIFOLD “O” RINGS (FIG.160).
Fig.160
Mount the manifold revolving on the cylinder
flange by using some grease to make the
operation easy.
Install the washer #2 (Fig.158) and fit the
screw #1 (Fig.158) by using green loctite.
Mount the piston release locking valve (
6.5.2).
Install the locking valve (
6.5.1).
Replace the small and big cylinder flange O
rings.
Mount the rear flange on the chuck cylinder
(
6.5.1).
Verify if the machine works fine.
6.6 SADDLE CYLINDER SLIDING
HYDRAULIC PRESSURE : CHECK
AND ADJUSTMENT
:
1h
:
End wrenches 10, 17, 19, 17mm socket
wrench, 6mm Allen wrench, rubber hammer,
wrench adjustment of saddle clearance,
manometer with adapter.
L
:
Incorrect pressure may cause the following
malfunction:
1. Low bead breaker power.
2. Slow
saddle
sliding.
TO CHECK THE SLIDING PRESSURE:
Remove the pin #1 (Fig.161).
Pull out the pin #2 and remove the mobile
table #3 (Fig.161)
Summary of Contents for KING 5600
