Service Manual 04/2010 Rev.B
122
Mount the robotic rotor
7.6.
Mount the rotation proof pin
7.9.
Mount the mount – dismount tool.
Make the screw support tool holder
adjustment
7.13.
Mount the hook protection (
6.1 Fig.140).
Verify if the machine works fine and if all
screws are well adjusted.
Grease all parts through the greasers.
7.18 MOUNT – DISMOUNT TOOL
:
1h
:
End wrenches 11,13mm, socket wrench
30mm, rubber hammer.
L
:
The mount – dismount tool is composed by
the hook and the bead breaker disk.
1.
:
The hook needs to be replaced in cases of
mechanical breakage only.
2.
:
The bead breaker disk may show the
following inconveniences:
A.
:
Excess of play.
B.
:
Mechanical breakage.
TO CHECK THE BEAD BREAKER DISK:
Move up and down the disk by hands.
If the disk shows a considerable play, try to
reduce this play as following (Fig.290):
Remove the 8mm screw #1.
Remove the plate #2 .
Tighten the screw #3 by using impact
machine.
Fig.290
If after tightening the disk still show the play, it
needs to be replaced.
If after tightening the disk does not show play
anymore, mount the plate #2 and lock it firmly
with 8mm screw #1(Fig.290).
IMPORTANT!
IF THE PLATE HOLE #2 DOES NOT MATCH
WITH THE 8mm THREADED HOLE, TURN THE
PLATE.
TO REPLACE THE BEAD BREAKER DISK:
Take away the defective disk (Fig.291).
Remove the washers #1 and #2 (Fig.291)
Remove the hardened bushing #3 from the
disk (Fig.291).
Remove
the
greaser.
Take the new one and grease it by using
white grease.
Install the greaser.
Insert the bushing #3 (Fig.291).
Place the disk on the hook.
Place a washer #1 (Fig.291) on top of the
disk.
Place a washer #2 (Fig.291) over the #1 one.
Insert half screw #3 (Fig.290)
Place a washer #1 (Fig.291) on the bottom of
the disk.
Place a washer #2 (Fig.291) under the #1
one.
Insert second half of screw #3 (Fig.290) and
tighten it.
Check if the disk turns free and if there is yet
play.
Fig.291
In case the disk does not turn free, check if
one or both washers #2 (Fig.291) have been
locked between the bushing 3# and the
washers #2 (Fig.291).
TO REPLACE THE HOOK:
Remove the disk by following the above
instructions.
Summary of Contents for KING 5600
