45
EFFECT Parameters > FX1–FX3
DEFRETTER BASS
This simulates a fretless bass.
Parameter
Value
Explanation
SENS
0–100
This controls the input sensitivity of
the defretter.
ATTACK
0–100
Adjusts the attack of the picking
sound.
TONE
-50–+50
Adjusts the amount of blurring
between the notes.
EFFECT LEVEL
0–100
Adjusts the volume of the effect
sound.
DIRECT LEVEL
0–100
Adjusts the volume of the direct
sound.
VARIATION
PATCH, 01–10
DEFRETTER BASS settings can be
saved/loaded as ten variations.
A saved VARIATION can be loaded
into a different patch, which is
convenient when you’re creating
sounds.
DELAY
Adds delayed sound to the direct sound, giving more body to the
sound or creating special effects.
Parameter
Value
Explanation
TYPE
Selects the delay type “TYPE” (p. 46).
* The stereo effect is canceled if a mono effect or
AMP Modeling is connected after a stereo delay
effect.
TIME
*1 *12
1 ms–2000
ms, BPM
`
–
Œ
Adjusts the delay time.
D1 TIME
D2 TIME
*2 *12
FEEDBACK
*3
0–100
This sets the amount of delay sound
returned to the input. A higher
value will increase the number of
the delay repeats.
D1 FEEDBACK
D2 FEEDBACK
*2
EFFECT LEVEL
*4
0–120
Adjusts the volume of the delay
sound.
D1 EFFECT
LEVEL
D2 EFFECT
LEVEL
*2
HIGH CUT
*3
20.0 Hz–16.0
kHz, FLAT
This sets the frequency at which the
high cut filter begins to take effect.
When FLAT is selected, the high cut
filter will have no effect.
D1 HIGH CUT
D2 HIGH CUT
*2
TAP TIME
*6
0–100%
Adjusts the delay time of the
right channel delay. This setting
adjusts the R channel delay time
relative to the L channel delay time
(considered as 100%).
Parameter
Value
Explanation
MOD RATE
*7
0–100
Adjusts the modulation rate of the
delay sound.
MOD DEPTH
*7
0–100
Adjusts the modulation depth of the
delay sound.
TRIGGER
*8
OFF, ON
If this is ON, the WARP effect is
applied.
MODE
*9
RISE
0
FALL
Rotation stops when you switch
TRIGGER from ON to OFF.
RISE
0
FADE
When you switch TRIGGER from
ON to OFF, fade-out occurs while
continuing the rotation.
TRIGGER
*9
OFF, ON
The TWIST effect is applied when
you turn this ON.
RISE TIME
*9
0–100
This parameter adjusts the amount
of time it is to take for the effect to
transition to the maximum.
FALL TIME
*9 *10
0–100
This parameter adjusts the amount
of time it is to take for the effect to
transition to the original.
FADE TIME
*9 *11
0–100
Adjusts the fade-out time.
DIRECT LEVEL
*5
0–100
Adjusts the volume of the direct
sound.
CARRY OVER
OFF, ON
Specifies whether the effect sound
remains when you turn off the
effect, or does not remain.
BPM
40–250
Adjusts the BPM value for each
patch.
VARIATION
PATCH, 01–10
DELAY settings can be saved/loaded
as ten variations.
A saved VARIATION can be loaded
into a different patch, which is
convenient when you’re creating
sounds.
These variations are shared with the
MASTER DELAY setting.
*1 Valid when the TYPE is set to other than DUAL-S, DUAL-P, DUAL
L/R, or TWIST.
*2 Valid when the TYPE is set to DUAL-S, DUAL-P, or DUAL L/R.
*3 Valid when the TYPE is set to other than DUAL-S, DUAL-P, DUAL
L/R, WARP or TWIST.
*4 Valid when the TYPE is set to other than DUAL-S, DUAL-P, or DUAL
L/R.
*5 Valid when the TYPE is set to other than WARP or TWIST.
*6 Valid when the TYPE is set to PAN.
*7 Valid when the TYPE is set to MOD.
*8 Valid when the TYPE is set to WARP.
*9 Valid when the TYPE is set to TWIST.
*10 Valid when the MODE is set to RISE
0
FALL.
*11 Valid when the MODE is set to RISE
0
FADE.
*12 Refer to “About effects when a note value is selected as a setting”
