Bosch Rexroth VT-VPCD Series Operating Instructions Manual Download Page 30

Page: 30 / 58

Company Registered in England No: 4167649 VAT Registration No: 732 5692 25 BS EN ISO 9001:2008 No: LRQ 0964389

+44 (0)1204 699 959

[email protected]

Hyquip Limited New Brunswick Street Horwich Bolton Lancashire BL6 7JB UK

www.hyquip.co.uk

/web/index

30/60 Installation

Bosch Rexroth AG

, VT-VPCD, RE 30028-B/09.13

7.3 Installation

conditions

The control electronics VT-VPCD is designed for installation in a 19“ rack or an

open card holder. Suitable card holders are listed in the following Chapter 7.4

“Recommended accessories“.

▶

Provide an operating voltage of 24 VDC.

▶

Adhere to the ambient temperature range permitted according to the data sheet.

7.4 Recommended

accessories

For connecting the control electronics VT-VPCD we recommend the use of the

following accessories, which are not included in the scope of supply, but which you

can order separately from Bosch Rexroth:

Table 11: Accessories

Component

Material number

Data sheet

VT 12302-3X/1, closed card holder, 64-pin edge connector
VT 12302-3x/2-64G Dual CARD HOLD

R900784153
R978009974

RE 30103
RE 30103

Open card holder VT 3002-1-2X/64 G

R900016484

RE 29928

Power supply unit VT-NE30-2X/

R901082348

RE 29929

Mating connector for proportional valve solenoid a, color: gray

R901017010

Mating connector for proportional valve solenoid b, color:

black

R901017011

4-pin mating connector for swivel angle transducer
AWXF004D01

R900023126

Serial interface cable for control electronics

R900776897

USB converter for connection to the serial interface

R901066684

The open card holder may only be used for installation in a control cabinet; it does not provide

electric shock protection.

If no voltage supply is provided on the system side.

7.5

Installing the VT-VPCD

Please observe the following notes when installing the VT-VPCD control electronics:

For the installation, observe the notes given in the data sheet on applied standards

and operating conditions.

Use low-capacitance cables.

Install cable connections without intermediate terminals whenever possible.

Install sensor cables separately.

The presence of electromagnetic sources of interference (e.g. frequency converter)

in the direct vicinity of the control electronics is not permitted.

The distance to aerial lines, radio sources and radar equipment must be at least

1 m.

Do not install solenoid and signal cables near power cables.

Use shielded cables (EMC-compliant) as valve cables.

Execute the installation so that when the diﬀerential inputs are used both inputs

are activated or deactivated simultaneously.

Use relays with gold-plated contacts for switching command values (small voltages,

small currents).

Do not use adhesives, sealants or insulating agents that contain silicone.

The system ground is an essential integral part of EMC protection of the control

electronics. Here, interference, which is transported to the control electronics via

data and voltage supply cables, is dissipated. This function can only be ensured, if the

Summary of Contents for Rexroth VT-VPCD Series



























































Search results

Summary of Contents for Rexroth VT-VPCD Series

Reviews:

Related manuals for Rexroth VT-VPCD Series

Brands by name

Popular brands

Bosch Rexroth VT-VPCD Series, Operating Instructions Manual

Search results

Summary of Contents for Rexroth VT-VPCD Series

Reviews:

Related manuals for Rexroth VT-VPCD Series

Brands by name

Popular brands