Bosch Rexroth VT-VPCD Series Operating Instructions Manual Download Page 12

Page: 12 / 58

Company Registered in England No: 4167649 VAT Registration No: 732 5692 25 BS EN ISO 9001:2008 No: LRQ 0964389

+44 (0)1204 699 959

[email protected]

Hyquip Limited New Brunswick Street Horwich Bolton Lancashire BL6 7JB UK

www.hyquip.co.uk

/web/index

12/60

General notes on damage to material and the product

Bosch Rexroth AG

, VT-VPCD, RE 30028-B/09.13

3 General notes on damage to material and

the product

The warranty is valid exclusively for the conﬁguration delivered.

Warranty claims will be rejected in the case of improper installation,

commissioning and operation as well as in the case of use not in accordance with

the intended purpose and/or improper handling.

NOTICE

High voltage!

Possible damage to the control electronics.

▶

Wire the control electronics only when it is disconnected from the power supply.

Overheating!

Possible damage to the control electronics.

▶

Adhere to the ambient conditions according to the data sheet.

▶

Do not use free-wheeling diodes in the solenoid cables.

▶

Ensure suﬃcient ventilation of air.

Overloading!

Risk of overloading and damage to supply cables in the case of insuﬃcient

dimensioning and/or operation with several electrical devices.

▶

Provide current limitation by overload protection.

▶

Select an appropriate rating of power supply unit and cables.

Short-circuit!

Risk of overloading of and damage to the supply cable in the case of a defect of

electrical equipment.

▶

Provide current limitation by means of overload protection.

Electrostatic discharge!

Risk of damage to components of the control electronics.

▶

Provide equipotential bonding to discharge static voltage from your body.

▶

Work in a safe environment.

▶

Do not use devices that generate or have static discharge in the working

environment.

▶

Do not carry out any work on the control electronics in environments that could

generate static charges.

▶

Handle the control electronics with care. Do not touch exposed connection pins

and sensitive components of the electronics.

▶

Transport and store the control electronics carefully in the original packaging

provided for this purpose.

Wrong cables! Voltage loss, scorching of cable!

Risk of damage to the product.

▶

For solenoid cables up to 50 m long, use cable type LiYCY 1.5 mm², for position

transducer cables, cable type LiYCY 0.5 mm² shielded. For greater lengths,

please consult us.

Summary of Contents for Rexroth VT-VPCD Series



























































Search results

Summary of Contents for Rexroth VT-VPCD Series

Reviews:

Related manuals for Rexroth VT-VPCD Series

Brands by name

Popular brands

Bosch Rexroth VT-VPCD Series, Operating Instructions Manual

Search results

Summary of Contents for Rexroth VT-VPCD Series

Reviews:

Related manuals for Rexroth VT-VPCD Series

Brands by name

Popular brands