Bosch Rexroth VT-VPCD Series Operating Instructions Manual Download Page 48

Page: 48 / 58

Company Registered in England No: 4167649 VAT Registration No: 732 5692 25 BS EN ISO 9001:2008 No: LRQ 0964389

+44 (0)1204 699 959

[email protected]

Hyquip Limited New Brunswick Street Horwich Bolton Lancashire BL6 7JB UK

www.hyquip.co.uk

/web/index

48/60 Operation

Bosch Rexroth AG

, VT-VPCD, RE 30028-B/09.13

The control electronics is in the conﬁguration mode “EDIT Parameters”.

How to change from the operation mode to the conﬁguration mode:

Precondition: You are in the operation mode.

The display shows as running text the manufacturer’s name and the version number

of the control electronics or a text determined individually by you.

▶

Press the control keys “ENT” and “ESC” simultaneously (exception: for “EDIT

Parameters“, see above) and hold them down (for at least 2 seconds) until

“Setup” is shown on the display of the control electronics.

The control electronics is now in the setup mode.

How to exit the conﬁguration mode:

In the present example, the second level of the menu tree “Setup” was selected.

The display of the control electronics shows “Sprache/Language” as running text.

▶

Press the “ESC” control key.

The display shows “Setup” as running text.

▶

Press the control key “ESC”.

The display shows as running text the manufacturer’s name and the version

number of the control electronics or a text determined individually by you.

If no entry is made within a minute in the conﬁguration mode, the control

electronics automatically changes to the next higher level until the operation

mode is reached.

The control electronics VT-VPCD is fully operable in the conﬁguration mode.

How to change a parameter with the help of the control keys:

CAUTION!

Uncontrolled system behavior! When parameters are changed with the

help of the control keys of the control electronics, the entries are not checked for

the signal “enable active”.

▶

Do not change one or several analog inputs from voltage to current or from

current to voltage. When you change the type of one or several analog inputs, the

active value is not interpreted as desired.

Summary of Contents for Rexroth VT-VPCD Series



























































Search results

Summary of Contents for Rexroth VT-VPCD Series

Reviews:

Related manuals for Rexroth VT-VPCD Series

Brands by name

Popular brands

Bosch Rexroth VT-VPCD Series, Operating Instructions Manual

Search results

Summary of Contents for Rexroth VT-VPCD Series

Reviews:

Related manuals for Rexroth VT-VPCD Series

Brands by name

Popular brands