Bosch Rexroth VT-VPCD Series Operating Instructions Manual Download Page 10

Page: 10 / 58

Company Registered in England No: 4167649 VAT Registration No: 732 5692 25 BS EN ISO 9001:2008 No: LRQ 0964389

+44 (0)1204 699 959

[email protected]

Hyquip Limited New Brunswick Street Horwich Bolton Lancashire BL6 7JB UK

www.hyquip.co.uk

/web/index

10/60 Safety

instructions

Bosch Rexroth AG

, VT-VPCD, RE 30028-B/09.13

2.6 Product-speciﬁc safety instructions

WARNING

Hazardous movement!

Risk of injury due to incorrect activation of the pump control by the control

electronics and resulting unforeseeable machine movements.

▶

Only operate the control electronics in conjunction with the pump control

speciﬁed in the type code.

▶

If persons have to enter the hazard zone while the control is active, provide

superordinate monitoring functions or measures for personal safety at system

level. The plant manufacturer/user must rate and dimension these measures on

the basis of a risk and failure analysis according to the speciﬁc situation on site.

The safety regulations valid for the system must be taken into account for this.

The control electronics emits interference to other electronics within the permitted

limit values. This can cause malfunction in the control process.

▶

Only use electronics below the EMC limit values or provide appropriate

shielding.

The control electronics VT-VPCD responds to electromagnetic interference from

non-shielded, improperly installed or wrongly connected cables. If the limit values

given in the data sheet are exceeded, malfunction or uncontrolled movements are

possible.

▶

Adhere to the limit values speciﬁed in the data sheet, use only electronics below

the EMC limit values or provide proper shielding.

Electrostatic processes, an inadequate grounding concept or missing equipotential

bonding can lead to damage to the electronics and hence cause malfunction or

uncontrolled movements of the machine.

▶

Ensure proper grounding and provide equipotential bonding.

Using the product outside the given IP protection class can result in short-circuit

and malfunction and can therefore cause uncontrolled machine movements.

▶

Only use the product within the IP protection class and under ambient

conditions as given in the data sheet.

The control electronics VT-VPCD itself does not include safety functions for

personal safety and is therefore no safety-relevant component. The control

electronics merely serves to generate electrical functions of the pump controls.

▶

Provide safety functions for personal safety separately.

▶

Avoid contact with salt-containing environments and adhere to the ambient

conditions speciﬁed in the data sheet.

High pressure!

Risk of injury!

▶

Depressurize the relevant system section before carrying out any work on the

control electronics.

Summary of Contents for Rexroth VT-VPCD Series



























































Search results

Summary of Contents for Rexroth VT-VPCD Series

Reviews:

Related manuals for Rexroth VT-VPCD Series

Brands by name

Popular brands

Bosch Rexroth VT-VPCD Series, Operating Instructions Manual

Search results

Summary of Contents for Rexroth VT-VPCD Series

Reviews:

Related manuals for Rexroth VT-VPCD Series

Brands by name

Popular brands