Bosch Rexroth HMU05.1N Series Page 115 Project Planning Manual Download

Page: 115 / 410

Components

Supply unit HMU05.1N-…

F0140-0350 (110 kW size)

F0170-0430 (132 kW size)

F0220-0510 (160 kW size)

F0270-0660 (200 kW size)

F0340-0820 (250 kW size)

F0430-1040 (315 kW size)

F0540-1300 (400 kW size)

F0680-1690 (500 kW size)

Mains choke HNL05.1R-

0219-N0218

✓

0182-N0262

✓

0135-N0327

✓

0117-N0409

✓

0130-N0514

✓

0113-N0652

✓

0100-N0811

✓

0094-N1019

✓

Preconnected choke

HNL05.1R-

0045-N0327

✓

0054-N0409

✓

0043-N0514

✓

0050-N0652

✓

0040-N0811

✓

0040-N1019

✓

Mains capacitor

HNC05.1N-

0050

✓

0075

✓

0100

✓

Mains filter HNF05.1A-

500N-R0250

✓

500N-R0320

✓

500N-R0400

✓

500N-R0600

✓

500N-R1000

✓

500N-R1600

✓

Tab. 4-22:

Mains connection components

DOK-INDRV*-HXX05******-PR02-EN-P

Bosch Rexroth AG

113/407

Rexroth IndraDrive ML Drive Systems with HMU05

Combining the individual components

Summary of Contents for Rexroth HMU05.1N Series



























































































































































































































































































































































































































Search results

Summary of Contents for Rexroth HMU05.1N Series

Reviews:

Related manuals for Rexroth HMU05.1N Series

Brands by name

Popular brands

Bosch Rexroth HMU05.1N Series, Project Planning Manual

Search results

Summary of Contents for Rexroth HMU05.1N Series

Reviews:

Related manuals for Rexroth HMU05.1N Series

Brands by name

Popular brands