Bosch Rexroth HMU05.1N Series Page 62 Project Planning Manual Download

Page: 62 / 410

4.4

Installation conditions

4.4.1

Ambient and operating conditions

Lethal electric shock by live parts with more

than 50 V!

WARNING

Exclusively operate the device
●

with plugged on connectors (even if there haven't been any lines con‐

nected to the connectors) and

●

with connected equipment grounding conductor!

Control cabinet

The devices in the Rexroth IndraDrive ML product range, as well as their ad‐

ditional components (except for some braking resistors), have to be mounted

in control cabinets.
Check that the ambient and operating conditions, in particular the control

cabinet temperature, are observed by calculating the heat levels in the con‐

trol cabinet. Afterwards, make the corresponding measurements to confirm

that ambient and operating conditions have actually been observed. The

power dissipation is indicated in the technical data of the individual compo‐

nents as an important input value for calculating the heat levels.
Ambient and operating conditions

Description

Symbol

Unit

Value

Conductive dirt contamination

Not allowed

(You can protect the devices against conductive dirt

contamination, e.g., by mounting them in control cab‐

inets with a degree of protection of IP54 in accord‐

ance with IEC529.)

Degree of protection (IEC529)

IP00

Use within scope of CSA / UL

For use in NFPA 79 Applications only!

Temperature during storage

see

chapter 5.4 "Storing components" on page 121

Temperature during transport

see

chapter 5.3 "Transporting components" on page

120

Allowed mounting position

Installation altitude

nenn

1000

Ambient temperature range

a_work

°C

0 … 40

Bosch Rexroth AG

DOK-INDRV*-HXX05******-PR02-EN-P

60/407

Rexroth IndraDrive ML Drive Systems with HMU05

Combining the individual components

Summary of Contents for Rexroth HMU05.1N Series



























































































































































































































































































































































































































Search results

Summary of Contents for Rexroth HMU05.1N Series

Reviews:

Related manuals for Rexroth HMU05.1N Series

Brands by name

Popular brands

Bosch Rexroth HMU05.1N Series, Project Planning Manual

Search results

Summary of Contents for Rexroth HMU05.1N Series

Reviews:

Related manuals for Rexroth HMU05.1N Series

Brands by name

Popular brands