Bosch CCT 3 Series, Test Instructions

Page: 26 / 50

en
Contents English
1 690 386 058 2018-01-30
|
Robert Bosch GmbH
26 | SCT / CCT / EL |
1. Symbols used 27
1.1 In the documentation 27
1.1.1 Warning notices -
Structure and meaning 27
1.1.2 Symbols in this documentation 27
1.2 On the product 27
2. User instructions 27
2.1 Test devices 27
2.1.1 Test template 1 690 385 006 27
2.1.2 Test board 1 690 382 354 28
2.1.3 Laser module 1 690 381 124 28
2.2 Test requirements 28
2.3 Definition of the angle being checked 28
2.4 Requirements 28
3. Overview of calibration and adjustment
devices 29
3.1 SCT 415 / CCT 3100 29
3.2 EL 52425 (Opel) 29
3.3 SCT 416 / CCT 3500 30
3.4 SCT 141x 30
3.5 SCT 410 31
4. Checking standard components 31
4.1 Checking the precision measuring bar 31
4.1.1 Checking the L-bracket (also for EL
52425) 32
4.1.2 Replacing the spirit level for the roll
angle on the L-bracket (also for
EL 52425) 32
4.1.3 Replacing the spirit level for the pitch
angle on the L-bracket (also for
EL 52425) 32
4.1.4 Checking the slides on the precision
measuring bar 33
4.2 Testing the laser module P-Assist S5
1 690 381 124 / 1 690 381 174
33
4.2.1 Checking the laser beam length 33
4.2.2 Checking the laser beam width 33
4.2.3 Checking the P-Assist S5 play 33
4.2.4 Checking the P-Assist S5 in laser
mount A 34
4.2.5 Checking the P-Assist S5 in laser
mount B 35
4.2.6 Checking the P-Assist S5 for rotation 35
4.3 Checking the calibration targets 1 690 382 xxx 37
5. Maintenance SCT 415/ SCT 416 / CCT 3100 /
CCT 3500 / EL 52425
37
5.1 Entire unit 37
5.1.1 Checking the roll angle and pitch
angle
37
5.1.2 Checking the pitch angle on the
slides
38
5.1.3 Checking the yaw angle (SCT 416 /
CCT 3500 only) 39
5.2 Components 41
5.2.1 Checking the post 41
5.2.2 Slide on the post 41
5.2.3 Base plate 41
5.2.4 Positioning units 42
5.2.5 Adjustment beam 43
5.2.6 Checking the reference boards 43
5.2.7 Checking the alignment lasers 44
6. Maintenance SCT 141x 45
6.1 Entire unit 45
6.1.1 Checking the pitch angle 45
6.1.2 Checking the yaw angle 46
6.2 Components 46
6.2.1 Checking the end stops 46
6.2.2 Checking the mounts 47
6.2.3 Checking the position indicator 47
6.2.4 Checking the tape measure holder 47
7. Maintenance SCT 410 47
7.1 Components 47
7.1.1 Checking the socket pin 47
7.1.2 Check the angle mounting bracket
and clamp 47
en
Contents English