manualshive.com logo in svg

BMW Motorrad R 1250 GS 2020, Rider'S Manual

Share
Download
BMW Motorrad R 1250 GS 2020 Rider'S Manual Download Page 77

71

The settings can be reset to

factory settings:

Riding mode settings reset

(

71).

Adjusting Dynamic Pro

Select PRO riding mode

(

70).

Set systems as for

ENDURO

PRO riding mode

.

Riding mode settings reset

Select PRO riding mode

(

70).

Select

Reset

and confirm.

The following factory settings

apply to

ENDURO PRO RID-

ING MODE

:

ENGINE

:

Road

DTC

:

Enduro Pro

ABS

:

Enduro Pro

The following factory settings

apply to

DYNAMIC PRO RID-

ING MODE

:

ENGINE

:

Dynamic

DTC

:

Dyna Pro

ABS

:

Dynamic

ADAPTIVE CRUISE CONTROL

with speed control

OE

Display while adjusting

(Speed Limit Info not active)

The icon

1

for the adaptive

cruise control is displayed in

the Pure Ride view and in the

upper status line.

Display while adjusting

(Speed Limit Info active)

The icon

1

for the adaptive

cruise control is displayed in

the Pure Ride view and in the

upper status line.

Summary of Contents for R 1250 GS 2020







































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands