manualshive.com logo in svg

BMW Motorrad R 1250 GS 2020, Rider'S Manual

Share
Download
BMW Motorrad R 1250 GS 2020 Rider'S Manual Download Page 134

128

RIDING

After riding off-road

BMW Motorrad recommends

the following after riding off-

road:

Tire pressure

WARNING

When driving off-road, lower

tire pressure than riding on

paved roads

Risk of accident due to

poorer handling characteris-

tics.

Ensure proper tire inflation

pressure.

Brakes

WARNING

Riding on unpaved or dirty

roads

Delayed braking effect due to

dirty brake discs and brake

pads

Brake early until the brakes

are clean again.

ATTENTION

Riding on unpaved or dirty

roads

Increased brake pad wear

Check the brake pad thick-

ness more often and replace

the brake pads sooner.

Spring preload and damping

WARNING

Modified values for spring

preload and spring strut

damping when riding off-

road

Poorer handling characteris-

tics on paved roads

Set correct spring preload

and correct spring strut

damping before leaving off-

road terrain.

Rims

BMW Motorrad recommends

checking the rims for possible

damage after riding off-road.

Summary of Contents for R 1250 GS 2020







































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands