manualshive.com logo in svg

BMW Motorrad R 1250 GS 2020, Rider'S Manual

Share
Download
BMW Motorrad R 1250 GS 2020 Rider'S Manual Download Page 205

199

ATTENTION

Folding down the carrying

handle when the case is

locked

Damage to the locking tab

Before folding down the

carrying handle, make sure

that the slot of the case lock

is perpendicular to the di-

rection of travel.

Shut the carrying handle

1

.

Turn the key

2

counterclock-

wise and remove.

Removing case

Turn key

1

clockwise.

Press and hold yellow locking

mechanism

2

and open carry-

ing handle

3

.

Pull the red release lever

1

upwards.

Locking mechanism

2

springs

open.

Fully open the locking mecha-

nism.

Remove case on the carrying

handle from the bracket.

Attaching a case

Pull the red release lever

1

upwards.

Locking mechanism

2

springs

open.

Summary of Contents for R 1250 GS 2020







































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands