BMW Motorrad R 1250 GS 2020 Rider'S Manual Download Page 233

Page: 233 / 294

227

FUEL

Recommended fuel quality

Super unleaded (max 15%

ethanol, E10/E15)

89 AKI (95 ROZ/RON)

90 AKI

Alternative fuel quality

Regular unleaded (restrictions

with regard to power and fuel

consumption). (max 15%

ethanol, E10/E15)

87 AKI (91 ROZ/RON)

87 AKI

Usable fuel quantity

Approx. 5.3 gal (Approx. 20 l)

Reserve fuel quantity

Approx. 1.1 gal (Approx. 4 l)

Fuel consumption

50 mpg (4.75 l/100 km), in

accordance with WMTC

CO2 emissions

110 g/km, according to

WMTC

Emission standard

TIER 2, measured in accor-

dance with FTP75

Summary of Contents for R 1250 GS 2020







































































































































































































































































































Search results

Summary of Contents for R 1250 GS 2020

Reviews:

Brands by name

Popular brands

BMW Motorrad R 1250 GS 2020, Rider'S Manual

Search results

Summary of Contents for R 1250 GS 2020

Reviews:

Brands by name

Popular brands