BMW Motorrad R 1250 GS 2020 Rider'S Manual Download Page 237

Page: 237 / 294

231

SUSPENSION

Front wheel

Type of front suspension

BMW Telelever, upper fork

bridge tilt decoupled, leading

link mounted in engine and on

telescopic fork, centrally posi-

tioned spring strut supported

on leading link and frame

Design of the front-wheel

suspension

Central spring strut with coil

spring

with Dynamic ESA

Central spring strut with coil

spring and expansion tank,

electrically adjustable rebound-

stage and compression damp-

ing

Spring travel, front

7.5 in (190 mm), on front

wheel

with sports suspension

8.3 in (210 mm), on front

wheel

with lowered

6.2 in (158 mm), on front

wheel

Summary of Contents for R 1250 GS 2020







































































































































































































































































































Search results

Summary of Contents for R 1250 GS 2020

Reviews:

Brands by name

Popular brands

BMW Motorrad R 1250 GS 2020, Rider'S Manual

Search results

Summary of Contents for R 1250 GS 2020

Reviews:

Brands by name

Popular brands