manualshive.com logo in svg

BMW Motorrad R 1250 GS 2020, Rider'S Manual

Share
Download
BMW Motorrad R 1250 GS 2020 Rider'S Manual Download Page 41

35

High beam faulty!

Turn indicator front
left faulty!

or

Turn

indicator front right
faulty!

Low beam faulty!

Front parking lamp
faulty!
Daytime running
light faulty!

with additional headlight

OE

Left auxiliary
headlight faulty!

or

Right auxiliary

headlight faulty!

Tail light faulty!

Brake light faulty!

Rear left turn
signal faulty!

or

Rear right turn signal
faulty!

License plate light
faulty!

Have checked by a spe-
cialist workshop.

WARNING

Overlooking the vehicle in

traffic due to a defective

light source on the vehicle

Safety risk

Replace defective light

sources as quickly as

possible. For details please

contact a specialist service

facility, preferably an

authorized BMW Motorrad

Retailer.

Possible cause:

One or more light sources are

faulty.

Locate defective bulb with

visual check.

Have the LED light source

replaced in full; for details

please contact a specialist

workshop, preferably an au-

thorized BMW Motorrad re-

tailer.

Anti-theft alarm battery low

charge

with anti-theft alarm system

(DWA)

OE

Anti-theft alarm
batt. capacity low.

No limitations. Arrange
an appointment at a spe-
cialist workshop.

Summary of Contents for R 1250 GS 2020







































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands