BMW Motorrad R 1250 GS 2020 Rider'S Manual Download Page 173

Page: 173 / 294

167

Pressure point must be clearly

perceptible.

If no clear pressure points are

perceptible:

ATTENTION

Improper working on the

brake system

Endangering of the operating

safety of the brake system

Have all work on the brake

system carried out by ex-

perts.

Have the brakes checked

at an authorized workshop,

preferably an authorized

BMW Motorrad retailer.

Checking the front brake pad

thickness

Park the motorcycle, making

sure that the ground is firm

and level.

Visually inspect the brake pad

thickness on the left and right.

Viewing direction: between

wheel and front suspension

toward brake pads

Front brake-pad wear

limit

0.04 in (1.0 mm) (Only fric-

tion material without car-

rier plate. The wear marks

(grooves) must be clearly visi-

ble.)

If the wear marks are no longer

clearly visible:

Summary of Contents for R 1250 GS 2020







































































































































































































































































































Search results

Summary of Contents for R 1250 GS 2020

Reviews:

Brands by name

Popular brands

BMW Motorrad R 1250 GS 2020, Rider'S Manual

Search results

Summary of Contents for R 1250 GS 2020

Reviews:

Brands by name

Popular brands