manualshive.com logo in svg

BMW Motorrad R 1250 GS 2020, Rider'S Manual

Share
Download
BMW Motorrad R 1250 GS 2020 Rider'S Manual Download Page 207

201

The following values apply for

the combination described

here:

Maximum speed for rid-

ing with Vario case

max 112 mph (max

180 km/h)

Payload per Vario case

max 22 lbs (max 10 kg)

TOPCASE

Opening the topcase

with topcase

OA

Turn key

1

clockwise.

Press and hold yellow locking

mechanism

2

and open carry-

ing handle

3

.

Push forward yellow button

1

and open topcase lid at the

same time.

Adjust topcase volumes

with topcase

OA

Open topcase and empty it.

Lock swivel arm

1

into its

most forward position to ob-

tain the largest volume.

Lock swivel arm

1

as far back

as it goes to obtain the small-

est volume.

Close topcase.

Summary of Contents for R 1250 GS 2020







































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands