BMW Motorrad R 1250 GS 2020 Rider'S Manual Download Page 114

Page: 114 / 294

108

SETTING

WINDSHIELD

Adjusting the windshield

WARNING

Adjusting the windshield

while driving

Accident hazard

Only adjust the windshield

when the motorcycle is sta-

tionary.

Turn the adjustment wheel

clockwise to lower the wind-

shield.

Turn the adjustment wheel

counter-clockwise to raise the

windshield.

CLUTCH

Clutch

WARNING

Adjusting the clutch lever

while driving

Accident hazard

Adjust the clutch lever when

the motorcycle is stationary.

Turn the adjustment wheel

into the desired position.

The adjustment wheel can

be turned more easily if

you press the clutch lever for-

ward when doing so.

Four settings are available:

Position 1: smallest distance

between handlebar grip and

clutch lever

Position 4: largest distance

between handlebar grip and

clutch lever

Summary of Contents for R 1250 GS 2020







































































































































































































































































































Search results

Summary of Contents for R 1250 GS 2020

Reviews:

Brands by name

Popular brands

BMW Motorrad R 1250 GS 2020, Rider'S Manual

Search results

Summary of Contents for R 1250 GS 2020

Reviews:

Brands by name

Popular brands