Big Backyard HILLCREST F23270 Page 99 Installation And Operating Instructions Manual Download

Page: 99 / 112

[email protected]

Step 45: Connect Monkey Bar Assembly to Fort

Part 2

Drive 1 (0318) Ground Stake 10-1/2” into the ground at one (2382) MK Post on the inside of the assembly and

attach with 2 (S3) #8 x 2-1/2” Wood Screws. (fig. 45.3 and 45.4)

Hardware

Wood Parts

2 x

#8 x 2-1/2” Wood Screw

0318

Fig. 45.3

Fig. 45.4

Inside View

10-1/2” In Ground

2382

1 x

Ground Stake 1-1/4 x 1-1/2 x 14”

0318

WARNING:

To prevent tipping and avoid potential injury, stakes must

be driven 10-1/2” into ground. Digging or driving stakes can be dangerous

if you do not check first for underground wiring, cables or gas lines.

Summary of Contents for HILLCREST F23270

















































































































Search results

Summary of Contents for HILLCREST F23270

Reviews:

Related manuals for HILLCREST F23270

Brands by name

Popular brands

Big Backyard HILLCREST F23270, Installation And Operating Instructions Manual

Search results

Summary of Contents for HILLCREST F23270

Reviews:

Related manuals for HILLCREST F23270

Brands by name

Popular brands