Big Backyard HILLCREST F23270 Page 34 Installation And Operating Instructions Manual Download

Page: 34 / 112

[email protected]

Loosely attach (2395) SW Ground using 2 (H4) 1/4 x 4” Hex Bolts (with lock washer, flat washer and t-nut)

in the top holes, (2370) Floor Back using 2 (H5) 1/4 x 4-1/2” Hex Bolts (with lock washer, flat washer and t-nut)

in the bottom holes and (2389) SW Back using 4 (H5) 1/4 x 4-1/2” Hex Bolts (with lock washer, flat washer and

t-nut) to both (2383) Posts. (fig. 11.1)

Loosely attach (2390) SW Mount to (2370) Floor Back and (2389) SW Back with 2 (G5) 5/16 x 4-1/2” Hex

Bolts (with lock washer, flat washer and t-nut). (fig. 11.1)

Note: Pre-drill all holes using a 1/8” drill bit before installing the Lag Screws.
C:

Make sure the assembly is square then tighten all Hex Bolts from this step. Attach (2370) Floor Back to each

(2383) Post with 2 (LS3) 1/4 x 3” Lag Screw (with flat washer) and (2395) SW Ground to each (2383) Posts with

2 (S7) #12 x 2” Pan Screws (with flat washer). (fig. 11.1)

Tight to the bottom of (2370) Floor Back and bevelled edges flush to outside edge of (2383) Posts, attach 1

(2113) Gussett II to each side using 2 (LS3) 1/4 x 3” Lag Screws (with flat washer) per gusset. (fig. 11.1)

Step 11: Swing Wall Assembly

2 x

5/16 x 4-1/2” Hex Bolt (5/16” lock washer, 5/16” flat washer, 5/16” t-nut)

2 x

1/4 x 4” Hex Bolt (1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

6 x

1/4 x 4-1/2” Hex Bolt (1/4” lock washer, 1/4” flat washer, 1/4” t-nut)

6 x

1/4 x 3” Lag Screw (1/4” flat washer)

1 x

SW Back 5/4 x 6 x 46-5/8”

1 x

SW Mount 2 x 4 x 34-1/2”

1 x

Floor Back 5/4 x 5 x 46-3/4”

2 x

Gusset II 5/4 x 4 x 18-1/2”

1 x

SW Ground 1 x 5 x 87-7/8”

2389

2370

2390

Hardware

Wood Parts

Fig. 11.1

2389

2395

2390

2383

2113

LS3

2383

Notice holes towards top.

x 4

Cafe Wall

x 2

LS3

x 2 per

Gusset

with 3/16” flat

washer

Notice angled end
on this side.

with 3/16” flat

washer

2113

2370

2395

2 x

#12 x 2” Pan Screw

(with 3/16” flat washer)

LS3

x 2

1/4” lock

washer

1/4”

t-nut

1/4” flat

washer

5/16” lock

washer

5/16”

t-nut

(hidden)

5/16” flat

washer

1/4” flat

washer

Summary of Contents for HILLCREST F23270

















































































































Search results

Summary of Contents for HILLCREST F23270

Reviews:

Related manuals for HILLCREST F23270

Brands by name

Popular brands

Big Backyard HILLCREST F23270, Installation And Operating Instructions Manual

Search results

Summary of Contents for HILLCREST F23270

Reviews:

Related manuals for HILLCREST F23270

Brands by name

Popular brands