Big Backyard HILLCREST F23270 Installation And Operating Instructions Manual Download

Page: 81 / 112

[email protected]

Step 37: A Frame/Tunnel Floor Board Assembly

Tight to (2361) A Frame Upright on the Rock Wall side and flush to the outside edge of (2353) A Frame

Floor Support attach (2393) A Frame Floor A to each (2353) A Frame Floor Support with 4 (S2) #8 x 1-1/2”

Wood Screws. (fig 37.1)

Tight to (2361) A Frame Upright on the Ladder side and flush to the outside edge of (2353) A Frame Floor

Support attach (2423) A Frame Floor D to each (2353) A Frame Floor Support with 4 (S2) #8 x 1-1/2” Wood

Screws. (fig 37.1)

Place and evenly space (2425) A Frame Floor B and (2424) A Frame Floor C between the first 2 floor

boards, flush to the outside edge of (2353) A Frame Floor Support, then each floor board to both (2353) A

Frame Floor Supports with 4 (S2) #8 x 1-1/2” Wood Screws per floor board. (fig 37.1)

Notice the ends of the floor boards, make sure they are flush and angled as shown below.

Fig. 37.1

x 4

2361

Flush

2368

2353

Tight

2353

2393

2425

2424

2423

2368

2361

Tight

Flush

Note board orientation.

Hardware

16 x #8 x 1-1/2” Wood Screw

Wood Parts

1 x

A Frame Floor A 1 x 6 x 76-27/32”

1 x

A Frame Floor B 1 x 6 x 71-3/8”

1 x

A Frame Floor C 1 x 6 x 65-55/64”

1 x

A Frame Floor D 1 x 5 x 60-11/32”

2393

2423

2424

2425

Summary of Contents for HILLCREST F23270

















































































































Search results

Summary of Contents for HILLCREST F23270

Reviews:

Related manuals for HILLCREST F23270

Brands by name

Popular brands

Big Backyard HILLCREST F23270, Installation And Operating Instructions Manual

Search results

Summary of Contents for HILLCREST F23270

Reviews:

Related manuals for HILLCREST F23270

Brands by name

Popular brands