Big Backyard HILLCREST F23270 Installation And Operating Instructions Manual Download

Page: 84 / 112

[email protected]

Place (2397) Tunnel Joist tight to underside of the floor boards, covering the pilot holes, between (2362)

Back Tunnel Support and (2373) Front Tunnel Support. Attach (2397) Tunnel Joist to both supports with 2 (S3)

#8 x 2-1/2” Wood Screws per support. (fig 38.10 and 38.11)

Attach floor boards to (2397) Tunnel Joist and (2379) Mid Joist with 4 (S2) #8 x 1-1/2” Wood Screws per

board. (fig. 38.12 and 38.13)

Step 38: Connect A Frame to Fort

Part 3

Hardware

4 x

#8 x 2-1/2” Wood Screw

16x

#8 x 1-1/2” Wood Screw

Wood Parts

1 x

Tunnel Joist 2 x 3 x 18-1/4”

2397

Fig. 38.10

View from

Underneath

2397

Floor Boards

Fig. 38.12

Fig. 38.11

Fig. 38.13

x 16

(hidden)

2373

2379

(hidden)

x 2 per side

2362

2397

2373

Summary of Contents for HILLCREST F23270

















































































































Search results

Summary of Contents for HILLCREST F23270

Reviews:

Related manuals for HILLCREST F23270

Brands by name

Popular brands

Big Backyard HILLCREST F23270, Installation And Operating Instructions Manual

Search results

Summary of Contents for HILLCREST F23270

Reviews:

Related manuals for HILLCREST F23270

Brands by name

Popular brands