manualshive.com logo in svg

BETTCHER INDUSTRIES Quantum Flex X350, Operating Instructions/Spare Parts List

Share
Download
BETTCHER INDUSTRIES Quantum Flex X350 Operating Instructions/Spare Parts List Download Page 64

Maintenance

5-22

Maintenance

Manual No. 107334

Operating Instructions and Parts List for the Quantum Flex

®

 Trimmer

June 22, 2018

MAINTENANCE - WHIZARD

®

 FLEXSHAFT AND CASING 

ASSEMBLY (CONTINUED)

Replacement of Split Bearing (#3)

•

Rmove the driver assembly. 

Refer to Section 5, Removal of the driver assembly

•

Insert a small screwdriver into the split in the bearing.

•

Spread the bearing and slide over the shoulder on the driver.

•

Clean the surface of the coupling and apply Max-Z-Lube grease. 

Refer to Section 7,

 

Lubrication and Lubrication Equipment.

•

Hold the bearing with the inside cone facing the end of the coupling.

•

Push the bearing on until it snaps into position.

•

Install the driver assembly. 

Refer to Section 5, Installation of the Driver Assembly

COMPANY 

CONFIDENTIAL

Summary of Contents for Quantum Flex X350



























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands