manualshive.com logo in svg

BETTCHER INDUSTRIES Quantum Flex X350, Operating Instructions/Spare Parts List

Share
Download
BETTCHER INDUSTRIES Quantum Flex X350 Operating Instructions/Spare Parts List Download Page 35

Instructions for Operation

Manual No. 107334

Instructions for Operation

4-3

June 22, 2018

Operating Instructions and Parts List for the Quantum Flex

®

 Trimmer

OPERATING INSTRUCTIONS (CONTINUED)

Optional Disc Gauges for Models: 
X850, X1850, X1000 and X1300

Optional adjustable disc gauges are available for 
the X1000 and X1300 trimmers. 

Refer to Section 

7, Service Parts to order

.

To adjust depth:

•

Hold the handpiece with the blade facing

downward.

•

Turn the adjustment knob clockwise for a

thicker cut, or counterclockwise for a thinner

cut.

NOTE:

 Take care not to turn too far as the depth 

control hub may disengage from the shaft.

Adjustable Depth Gauge for Models: X880 (S&B), X1880, X1400 
and X1500 Only

These tools come equipped with an adjustable 
depth gauge for setting a controlled product trim 
thickness. The depth gauge can be adjusted for cuts 
up to ¼” thick.

 

A depth gauge setting device is also 

available. 

To adjust depth:

•

Hold the handpiece with the blade facing

downward.

•

Loosen the attachment screws at the base of

the plastic depth gauge.

•

Adjust the gauge setting by sliding it up or

down to the desired height.

•

Retighten the attachment screws.

 

 

 

  

 

 

COMPANY 

CONFIDENTIAL

Summary of Contents for Quantum Flex X350



























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands