manualshive.com logo in svg

BETTCHER INDUSTRIES Quantum Flex X350, Operating Instructions/Spare Parts List

Share
Download
BETTCHER INDUSTRIES Quantum Flex X350 Operating Instructions/Spare Parts List Download Page 53

Maintenance

Manual No. 107334

Maintenance

5-11

June 22, 2018

Operating Instructions and Parts List for the Quantum Flex

®

 Trimmer

DAILY INSPECTIONS & MAINTENANCE

Blade

•

Check for worn or chipped teeth.

•

Check for damage to the cutting edge.

WARNING

Inspection of all parts for excessive wear is critical to ensure proper and
safe operation. Vibration or lock-up may occur as a result of the use of 
excessively worn parts.

Sharp blades may cause cut injury!

Always disconnect power and remove the tool from the driveline or 
flexshaft and casing assembly prior to servicing.

Do not adjust handle or thumb support with the trimmer running, or with 
blade installed.

After sharpening blade, all abrasive dust must be completely removed 
from the handpiece. Disassemble the unit and carefully wash each piece 
with hot, soapy water and a small brush.

Prior to assembly, be sure all parts are clean and have been inspected for 
wear.

COMPANY 

CONFIDENTIAL

Summary of Contents for Quantum Flex X350



























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands