manualshive.com logo in svg

BETTCHER INDUSTRIES Quantum Flex X350, Operating Instructions/Spare Parts List

Share
Download
BETTCHER INDUSTRIES Quantum Flex X350 Operating Instructions/Spare Parts List Download Page 51

Manual No. 107334

Maintenance

5-9

June 22, 2018

Operating Instructions and Parts List for the Quantum Flex

®

 Trimmer

Maintenance

DISASSEMBLY OF HANDPIECE (CONTINUED)

Remove the Blade Housing and Cover Plate - Large Tools Only

•

Loosen cover retaining screws until the

cover is free.

NOTE:

 The screws will stay in the frame. 

•

Remove the blade housing.

•

Pull the pinion out of the frame.

Remove the Optional Depth Gauge / Disc Gauge from the Cover 
Plate

•

Loosen the two attachment screws located inside the depth gauge. It is not necessary to

remove the screws.

•

Slide the gauge upward until the depth gauge clamps come out of the cover plate grooves.

 

 

 

 

 

 

 

  

COMPANY 

CONFIDENTIAL

Summary of Contents for Quantum Flex X350



























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands