manualshive.com logo in svg

BETTCHER INDUSTRIES Quantum Flex X350, Operating Instructions/Spare Parts List

Share
Download
BETTCHER INDUSTRIES Quantum Flex X350 Operating Instructions/Spare Parts List Download Page 38

Instructions for Operation

4-6

Instructions for Operation

Manual No. 107334

Operating Instructions and Parts List for the Quantum Flex

®

 Trimmer

June 22, 2018

BLADE CHANGING - SMALL TOOLS

Blade Removal - Small Tools

Models: X350, X360, X440, X500, X505, X500A, X564, X620, X625, 
X620A

•

Hold the tool in your hand with the blade edge facing upward.

•

Loosen the two blade housing mounting screws about ½ turn.

•

Using ¼" nut driver turn the cam clockwise about 1/8 of a turn until it locks the housing in

 

the open position.

•

Remove the blade from the blade housing.

WARNING

Sharp blades may cause cut injury!

For proper protection of hands, a protective glove should be used when 
operating this equipment and during the handling of blades. Metal mesh 
gloves are recommended for the free hand.

Keep hands away from moving blade.

 

 

 

 

COMPANY 

CONFIDENTIAL

Summary of Contents for Quantum Flex X350



























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands