BETTCHER INDUSTRIES Quantum Flex X350 Operating Instructions/Spare Parts List Download Page 45

Page: 45 / 154

Maintenance

Manual No. 107334

Maintenance

5-3

June 22, 2018

Operating Instructions and Parts List for the Quantum Flex

Trimmer

REMOVING QUANTUM FLEX

TRIMMER FROM THE WHIZARD

QUANTUM

DRIVELINE OR WHIZARD

FLEXSHAFT AND CASING

ASSEMBLY

Non-Disconnect Models

•

Hold Quantum Flex

Trimmer in the hand

you will use in operation.

•

With opposite hand, press the latch button

in the handle retaining knob.

•

The driveline or flexshaft casing assembly

should eject from the handl

Disconnect Models

•

Release the disconnect lever and the

driveline or flexshaft casing assembly

should partially eject from the handle.

•

With the opposite hand, press the latch

button in the handle retaining knob.

•

The driveline or flexshaft casing assembly

should eject from the handle.

COMPANY

CONFIDENTIAL

Summary of Contents for Quantum Flex X350



























































































































































Search results

Summary of Contents for Quantum Flex X350

Reviews:

Brands by name

Popular brands

BETTCHER INDUSTRIES Quantum Flex X350, Operating Instructions/Spare Parts List

Search results

Summary of Contents for Quantum Flex X350

Reviews:

Brands by name

Popular brands