BETTCHER INDUSTRIES Quantum Flex X350 Operating Instructions/Spare Parts List Download Page 143

Page: 143 / 154

Service Parts

Manual No. 107334

Service Parts

7-59

June 22, 2018

Operating Instructions and Parts List for the Quantum Flex

Trimmer

WHIZARD

1/4” FLEXSHAFT AND CASING ASSEMBLY - SMALL

TOOLS ONLY (CONTINUED)

FOR USE WITH UN-84 AND ULTRA DRIVE MOTORS

TO CONVERT WHIZARD

SERIES II FLEXSHAFT AND CASING ASSEMBLIES FOR

USE WITH QUANTUM FLEX

TOOLS:

To convert an existing flexshaft and casing assembly without disconnect that was previously used
to drive a Whizard

Series II tool, simply replace the casing latch collar, part number 183111,

with part number 105386. If you have a flexshaft and casing assembly with disconnect, replace
the lever mounting collar, part number 183110 with part number 105418.

ITEM

DESCRIPTION

WITHOUT DISCONNECT

WITH DISCONNECT

48”

60”

73”

84”

48”

60”

73”

84”

Casing Assembly Complete
(Includes 1,2,4,5)

107156

107157

107158

107159

------

Casing Assembly Complete
(Includes 1,4,5,7,8)

------

107160

107161

107162

107163

Casing Assembly

183771

183772

103498

183773

183771

183772

103498

183773

Casing Latch Collar

105386

------

Flexshaft

183837

183838

103504

183839

183837

183838

103504

183839

Nylon Washer

123314

Drive End Assembly
(Includes Items 5 and
6)

105441

Drive End Sub
Assembly

183129

Driver Assembly (Small
Tools)

104355

Lever Mounting Collar

------

105418

Disconnect Lever

------

183108

NOTICE

Whizard

Series II flexshaft and casing assemblies are not compatible

with Quantum Flex

Tools. Whizard

Series II flexshaft and casing

assemblies must be converted prior to use with Quantum Flex

tools.

COMPANY

CONFIDENTIAL

Summary of Contents for Quantum Flex X350



























































































































































Search results

Summary of Contents for Quantum Flex X350

Reviews:

Brands by name

Popular brands

BETTCHER INDUSTRIES Quantum Flex X350, Operating Instructions/Spare Parts List

Search results

Summary of Contents for Quantum Flex X350

Reviews:

Brands by name

Popular brands