manualshive.com logo in svg

BETTCHER INDUSTRIES Quantum Flex X350, Operating Instructions/Spare Parts List

Share
Download
BETTCHER INDUSTRIES Quantum Flex X350 Operating Instructions/Spare Parts List Download Page 39

Instructions for Operation

Manual No. 107334

Instructions for Operation

4-7

June 22, 2018

Operating Instructions and Parts List for the Quantum Flex

®

 Trimmer

BLADE CHANGING - SMALL TOOLS (CONTINUED)

Blade Installation - Small Tools
Models: X350, X360, X440, X500, X505, X500A, X564, X620, X625, 
X620A

•

Turn the tool over so that the blade

 

housing mounting screws are

 

pointing upward.

•

Loosen the two blade housing

 

mounting screws about 1/2 turn if

 

they are not loose already.

•

Using ¼" nut driver turn the cam

 

clockwise about 1/8 of a turn until it

 

locks the blade housing in the open

 

position.

•

Insert a new blade into the housing.

•

Turn the cam counter-clockwise about

 

1/8 of a turn to close the blade housing.

•

Tighten the two blade housing mounting

 

screws.

•

The blade should rotate freely.

WARNING! 

Make certain that the blade is 

free to rotate in the housing. If the blade does 
not turn freely, it may cause the tool to 
rotate in the hand.

NOTE:

 There is no adjustment in the blade 

housing on the small tools.

WARNING

Sharp blades may cause cut injury!

For proper protection of hands, a protective glove should be used when 
operating this equipment and during the handling of blades. Metal mesh 
gloves are recommended for the free hand.

Keep hands away from moving blade.

 

 

 

 

 

 

 

 !

 

COMPANY 

CONFIDENTIAL

Summary of Contents for Quantum Flex X350



























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands