manualshive.com logo in svg

BETTCHER INDUSTRIES Quantum Flex X350, Operating Instructions/Spare Parts List

Share
Download
BETTCHER INDUSTRIES Quantum Flex X350 Operating Instructions/Spare Parts List Download Page 60

Maintenance

5-18

Maintenance

Manual No. 107334

Operating Instructions and Parts List for the Quantum Flex

®

 Trimmer

June 22, 2018

DAILY INSPECTION AND MAINTENANCE - WHIZARD

®

 

FLEXSHAFT AND CASING ASSEMBLY

•

Inspect the casing for any cracks, tears, or other wear. If any damage is found, replace the

casing.

•

Remove the flexshaft from the casing and check for any flexshaft damage, such as broken

wires or kinking. If any damage is detected, replace the flexshaft.

•

Reinsert the flexshaft into the casing, making certain the flange of the flexshaft is pressed

against the bearing inside the casing.

•

Check the extension of the flexible shaft driver at the motor end. The flexible shaft driver

should extend past the motor end fitting. If the shaft extends less than 5/64", replace the

casing.

Bearing

Flex Shaft 

Driver

Casing

Motor End 

Fitting

COMPANY 

CONFIDENTIAL

Summary of Contents for Quantum Flex X350



























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands