manualshive.com logo in svg

BETTCHER INDUSTRIES Quantum Flex X350, Operating Instructions/Spare Parts List

Share
Download
BETTCHER INDUSTRIES Quantum Flex X350 Operating Instructions/Spare Parts List Download Page 49

Maintenance

Manual No. 107334

Maintenance

5-7

June 22, 2018

Operating Instructions and Parts List for the Quantum Flex

®

 Trimmer

DISASSEMBLY OF HANDPIECE (CONTINUED)

Remove the Handle Retaining Knob

•

Turn retaining knob counterclockwise.

Remove the Handle from the Tool

•

Pull the handle off the tube.

•

Remove the handle spacer ring or optional

thumb support.

•

Remove the grease cup and ring.

Remove the Blade Housing, Finger Guard, Cam Plate 
Assembly, and Cover Plate - Small Tools Only

•

Loosen both blade housing mounting

 

screws until the cam assembly is free.

NOTE:

 The screws will stay in the cam plate 

assembly.

•

Remove the blade housing.

•

Loosen both cover retaining screws until

 

the cover is free. The cover retaining

 

screws do not need to be completely

 

removed from the frame to remove the

 

cover.

•

Pull the pinion out of the frame.

 

  

 

 

 

 

  %

$

 

 

 

COMPANY 

CONFIDENTIAL

Summary of Contents for Quantum Flex X350



























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands