manualshive.com logo in svg

BETTCHER INDUSTRIES Quantum Flex X350, Operating Instructions/Spare Parts List

Share
Download
BETTCHER INDUSTRIES Quantum Flex X350 Operating Instructions/Spare Parts List Download Page 44

Maintenance

5-2

Maintenance

Manual No. 107334

Operating Instructions and Parts List for the Quantum Flex

®

 Trimmer

June 22, 2018

REMOVING WHIZARD QUANTUM

®

 DRIVELINE FROM THE 

WHIZARD QUANTUM

®

 DRIVE UNIT

Remove Whizard Quantum

®

 

Driveline from Disconnect Body

Hold driveline assembly around the top 

exposed portion, just below the disconnect 

body. Push casing retainer latch inward and 

pull driveline down and out of disconnect 

body.

REMOVING WHIZARD

®

 FLEXSHAFT AND CASING ASSEMBLY 

FROM THE WHIZARD

®

 UN-84 OR WHIZARD

®

 ULTRA DRIVE UNIT

Remove Whizard

®

 Flexshaft and 

Casing Assembly from Disconnect 
Body

Remove the Whizard

®

 Flexshaft and Casing 

Assembly from the drive unit by lifting the 
disconnect collar and pulling the adapter end of the 
flexshaft and casing assembly from the disconnect 
body.

DRIVELINE ASSEMBLY

DISCONNECT BODY

CASING RETAINER

LATCH

 

 

COMPANY 

CONFIDENTIAL

Summary of Contents for Quantum Flex X350



























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands