Belden 934 879-009 Manual Download Page 96

Page: 96 / 98

9.7 LEDs

9 Technical data

9.7 LEDs

Green

System/sensor power supply, voltage level

18 V <= U

+/- 1 V <=30 V

Red

System/sensor power supply, voltage level

< 18 V +/- 1 V or U

> 30 V +/- 1 V

Off

No system/sensor power supply

Green

Actuator power supply, voltage level

18 V <= U

+/- 1 V <=30 V

Red

Actuator power supply, voltage level

< 18 V +/- 1 V or U

> 30 V +/- 1 V

Off

No actuator power supply

X1…X8 A

Yellow

Channel status A "On"

Red

Periphery error (sensor or actuator overload/short-circuit)

DIA

Off

Not connected, status "Off", no error

White

Channel status B "On"

Red

Periphery error (actuator overload/short-circuit)

X1…X8 B

Off

Not connected, status "Off", no error

P1 Lnk/Act

Green

Ethernet connection exists to another subscriber. Link connection

created.

Flashing yellow

Data exchange with another subscriber.

P2 Lnk/Act

Off

No connection to another subscriber. No link, no data exchange.

Green

Device ready for operation

Flashing green

Device ready but not configured

Red

Serious error that cannot be resolved

Flashing red

Minor error that can be resolved: An incorrect or contradictory

configuration is classified as a minor error.

Alternately

flashing red/

green

The device is performing a self-test.

Off

Device is switched off.

Manual LioN-P EtherNet/IP

Version 2.0 11/2017

Summary of Contents for 934 879-009



































































































Search results

Summary of Contents for 934 879-009

Reviews:

Related manuals for 934 879-009

Brands by name

Popular brands

Belden 934 879-009, Manual

Search results

Summary of Contents for 934 879-009

Reviews:

Related manuals for 934 879-009

Brands by name

Popular brands