Beijer Electronics BFI-P2, Start-Up

Page: 27 / 31

Beijer Electronics Frequency Inverter BFI-P2
KI00306B 2020-03
www.beijer.se www.beijer.no www.beijer.dk www.beijerelectronics.com www.beijerelectronics.de www.beijerelektronik.com.tr
27 (31)
Description Display
range
Explanation
P0-01 1st Analog Input Value -100 % .. 100 % 100% = max input voltage for Analog input1, Terminal 6
P0-02 2nd Analog Input Value 0 to 100 % 100% = max input voltage for Analog input2, Terminal 10
P0-03 Digital Input Status 00000 to 11111 One digit per input starting with Digital In1 to the left
P0-04 Speed Reference Input -P1-01 … P1-01 Displayed in Hz if P-10 = 0, otherwise displayed in RPM
P0-05 Torque Controller Reference 0 to 500 % Displays the set point torque reference input
P0-07 Fieldbus Speed Reference -P1-01 … P1-01 Displays set point frequency received from Fieldbus interface
P0-08 PID Reference (Setpoint) 0 to 100 % Displays the setpoint input to the PID controller
P0-09 PID Feedback Level 0 to 100 % Displays the Feedback input signal to the PID controller
P0-10 PID Controller Output 0 to 100 % Displays the output level of the PID controller
P0-11 Motor Voltage 0 … 600V AC Value of RMS voltage applied to motor
P0-12 Output Torque % Displays instantaneous output torque level for the motor
P0-13 Trip Log Displays the four latest fault codes
P0-14 Motor Magnetising Current (Id) A Displays motor magnetising current after an auto tune
P0-15 Motor Rotor Current (Iq) A Displays motor rotor current after an auto tune
P0-16 DC Bus Voltage Ripple Level V Displays the level of ripple present on the DC Bus Voltage.
P0-17 Motor Stator resistance (Rs) Ω Displays measured motor stator resistance after an auto tune
P0-18 Motor Stator Inductance (Ls) H Displays measured motor stator inductance after an auto tune
P0-19 Motor Rotor Resistance (Rr) Ω Displays measured motor rotor resistance after an auto tune
P0-20 DC Bus Voltage 0 … 1000V dc Internal DC bus voltage
P0-21 Internal Temperature -20 … 100 °C Temperature of heatsink in °C
P0-25 Rotor Speed Hz / rpm
In Vector control mode, displays the estimated rotor speed of the motor or
measured rotor speed with Encoder Feedback
P0-26 kWh meter 0 to 999,9 When overflow P00-27 increases by 1 and reset to 0.
P0-27 MWh meter 0 to 65535 Displays the amount of energy consumed by the drive.
P0-28 Software Version I/O-version, I/O Checksum, DSP version, DSP checksum.
P0-29 Drive Type Frame size, Power rating and output phases
P0-30 Drive Serial Number Unique drive serial number.
P0-31 Total Run Time hours Displays the total operating time of the drive.
P0-35 Fan Run Time 0 .. 99999 hours Displays total operating time of internal cooling fans.
P0-36 DC Bus Voltage at Trip V DC Values logged before trip with 8 samples total (256 msec).
P0-37 DC Bus Voltage Ripple at Trip V DC Values logged before trip with 8 samples total (20 msec).
P0-38 Heatsink Temperature at Trip -20 … 100 °C Values logged before trip with 8 samples total (30 sec).
P0-39 Ambient Temperature at Trip °C Values logged before trip with 8 samples total (30 sec).
P0-40 Motor Current Log at Trip A Values logged before trip with 8 samples total (256 msec).
P0-41 Over Current Fault Counter Over Current fault counter
P0-42 Over Voltage Fault Counter Over Voltage fault counter
P0-43 Under Voltage Fault Counter Under Voltage fault counter
P0-44 Heatsink Over Temperature Heatsink Over Temperature fault counter
P0-45 Brake Chopper Short Circuit Brake Chopper Short Circuit fault counter
P0-46 Ambient Over Temperature Ambient Over Temperature fault counter
P0-49 Modbus RTU Modbus RTU communication fault counter
P0-58 Encoder Feedback Speed Value Hz / rpm
P0-60
Calculated Slip Speed Value (V/F
Mode Only)
%
When slip compensation is enabled using P1-10, the calculated motor slip is
displayed here. The raw value is displayed
P0-64 Switching Frequency kHz Displays the actual effective Switching frequency
P0-65 Drive Life Time Powered up time, hours, min, and sec
P0-70 Option Module ID-code Identifies Type of Option Module inoption module slot
P0-71 Fieldbus module ID Fieldbus module Identification Code
P0-74 L1 – L2 Input Voltage V Displays the supply voltage measured between L1 and L2 terminals
P0-75 L2 – L3 Input Voltage V Displays the supply voltage measured between L2 and L3 terminals
P0-76 L3 – L1 Input Voltage V Displays the supply voltage measured between L3 and L1 terminals
P0-77 Encoder Pulse Count (32bit) pulses Hi 16-bit and Lo 16-bit
P0-78 Test Parameter ¾
P0-79 Boot Loader/Motor Control version
P0-80 User Defined Internal Parameter Parameter P6-28 decides value to be shown