Bay Networks Baystream 7 Notice Download Page 48

Page: 48 / 140

BayStream 7.3 Documentation Change Notice

BayStream Multiservice Software Version 7.3

115385-D Rev 01

Refer to Statistics for information on generating and interpreting performance
reports using BayStream Statistical Data Collection software.

Line Byte Count for ATM Circuits

You can enable (and disable) the collection of Line Byte Count statistics for the
DS-3 and OC-3 ATM circuits. The Line Byte Count for ATM circuits is reported
in cells (SYNCH, HSSI, FDDI, and MUNICH logical lines are reported in bytes).

AtmizerVclTxPacketsOkWra
p

1.3.6.1.4.1.18.3.4.23.3.4.1.
18

Yes

AtmizerVclTxPacketsOk

1.3.6.1.4.1.18.3.4.23.3.4.1.
19

Yes

AtmizerVclTxCellsOkWrap

1.3.6.1.4.1.18.3.4.23.3.4.1.
20

Yes

AtmizerVclTxCellsOk

1.3.6.1.4.1.18.3.4.23.3.4.1.
21

Yes

AtmizerVclTxOamCount

1.3.6.1.4.1.18.3.4.23.3.4.1.
22

Yes

AtmizerVclTxFlowCtrlCount

1.3.6.1.4.1.18.3.4.23.3.4.1.
23

Yes

AtmizerVclTxOversizedSDU
s

1.3.6.1.4.1.18.3.4.23.3.4.1.
24

Yes

AtmizerVclTxLackBufCredits 1.3.6.1.4.1.18.3.4.23.3.4.1.

Yes

AtmizerVclTxLackPageCredi
ts

1.3.6.1.4.1.18.3.4.23.3.4.1.
26

Yes

8 - 0 (LSB)

Not Used

N/A

Table 5.

Atmizer Bit Mask

Bit

Atmizer Counter

Object ID

Default

Summary of Contents for Baystream 7













































































































































Search results

Summary of Contents for Baystream 7

Reviews:

Related manuals for Baystream 7

Brands by name

Popular brands

Bay Networks Baystream 7, Notice

Search results

Summary of Contents for Baystream 7

Reviews:

Related manuals for Baystream 7

Brands by name

Popular brands