manualshive.com logo in svg

Bay Networks 5782, User Manual

Share
Download
Bay Networks 5782 User Manual Download Page 88

Using the Model 5782 ATM Virtual Network Router

D-8

119557-A Rev. 00

Step 7. Specify a name for the configuration file.

                         Save configuration to a file.
                         -----------------------------

The Quick-Start configuration of the router is now complete and active.

Do you wish to save this configuration to a file? (y/n)[y]: 

Default file name is startup.cfg on the current volume.

NOTE: Do *NOT* name this file 'config'. Later, you may wish to rename 
      this file 'config' after you perform a named boot and verify its
      operation.

Enter file name [startup.cfg]:
-------------------------------------------------------------------------------
Step 8.  Test this initial IP interface configuration.

                                TEST IP Interface
                                -----------------

IP Interface 192.168.13.72 is up.

Testing local IP interface.

ping -IP 192.168.13.72 -r5
IP ping: 192.168.13.72 is alive (size = 16 bytes)
IP ping: 192.168.13.72 is alive (size = 16 bytes)
IP ping: 192.168.13.72 is alive (size = 16 bytes)
IP ping: 192.168.13.72 is alive (size = 16 bytes)
IP ping: 192.168.13.72 is alive (size = 16 bytes)

This test attempts to ping the Site Manager workstation.

NOTE:  If routing has not yet converged, an attempt
       to ping the Site Manager workstation may fail.  If
       this happens, you may either enter a new IP address or
       quit and wait a short period of time and try again from
       the TI command line.

Type q<return> to cancel this test.
Enter IP address of Site Manager workstation: 192.168.13.92
ping -IP 192.168.13.92 -p -r5
IP ping: 192.168.13.92 is alive (size = 16 bytes)
IP ping: 192.168.13.92 is alive (size = 16 bytes)
IP ping: 192.168.13.92 is alive (size = 16 bytes)
IP ping: 192.168.13.92 is alive (size = 16 bytes)
IP ping: 192.168.13.92 is alive (size = 16 bytes)

-------------------------------------------------------------------------------

Quick-Start Installation Completed.

Exiting... 
  More Mode: ON
  Lines per screen: 24

Summary of Contents for 5782











































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands