manualshive.com logo in svg

Bay Networks 5782, User Manual

Share
Download
Bay Networks 5782 User Manual Download Page 62

Using the Model 5782 ATM Virtual Network Router

3-8

119557-A Rev. 00

4.

Verify that the directory lists the Quick-Start installation files shown in 

Table 3-3

 (other files may appear in the directory). 

If your installation files or software image are not available, contact the Bay 
Networks Technical Solutions Center.

Booting with the ti_5000.cfg File

To prepare the Model 5782 VNR for initial configuration, you first boot it with the 
ti_5000.cfg file. The ti_5000.cfg file is an initial configuration file containing only 
the minimal information needed to boot the Model 5782 VNR. You then run the 
intallation script to add configuration information about your first IP interface.

When you complete the Quick-Start procedure, you save your new configuration 
information to a file called startup.cfg. Do not edit the ti_5000.cfg file or 
overwrite it with another configuration file.

If the installation fails, you must reboot the VNR with ti_5000.cfg before retrying 
the Quick-Start procedure. You also should boot with the ti_5000.cfg file if:

•

The router is currently running a configuration file other than ti_5000.cfg and 
you want to reconfigure the Model 5782 VNR from scratch.

•

You terminate the Quick-Start installation script before it completes the 
installation process.

Table 3-3.

Quick-Start Installation Files

File Name

File Type

areboot.ppc

Boot PROM for ATM routing engine

arediag.ppc

Diagnostic PROM for ATM routing 
engine

ti_5000.cfg

Initial configuration file

config

Default boot configuration file

debug.al

Alias file

install.bat

Installation script file

s5000.exe

Router software image

Summary of Contents for 5782











































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands