manualshive.com logo in svg

Bay Networks 5782, User Manual

Share
Download
Bay Networks 5782 User Manual Download Page 30

Using the Model 5782 ATM Virtual Network Router

1-8

119557-A Rev. 00

LAN Emulation

Bay Networks provides LAN emulation (LANE) services for Ethernet and token 
ring networks over ATM. These services are compatible with the ATM Forum 
LAN Emulation Over ATM specification.

LAN emulation allows interoperability between software applications residing on 
ATM end stations and on traditional LAN end stations.

ATM Q.2931 Signaling

The Model 5782 VNR supports ATM Forum UNI Version 3.0 and Version 3.1 
signaling protocol for SVCs, known as Q.2931. ATM signaling allows the router 
to dynamically establish, maintain, and clear a switched virtual connection at the 
user-to-network interface (UNI).

The signaling ATM adaptation layer (SAAL) resides between the ATM layer and 
Q.2931 (

Figure 1-3

). SAAL is a reliable transport layer for signaling messages 

sent between peer Q.2931 elements over the ATM layer.

IPX

XNS

RIP/SAP

RIP (XNS)

XNS

AppleTalk

RIP (XNS)

LLC2

AppleTalk

DLSw

Source Routing

IPv6

SR Spanning Tree

Translate/LB

IPv6

Table 1-1.

Protocols Supported for Standard PVCs and SVCs

 (continued)

PVC Using LLC/SNAP, 
NLPID, or NULL

SVC Using LLC/SNAP
or NULL (RFC 1577)

SVC Using LANE 802.3

SVC Using LANE 802.5

Summary of Contents for 5782











































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands