manualshive.com logo in svg

Bay Networks 5782, User Manual

Share
Download
Bay Networks 5782 User Manual Download Page 13

119557-A Rev. 00

xiii

Figures

Figure 1-1.

Model 5782 VNR in an ATM Network  ............................................................... 1-3

Figure 1-2.

Model 5782 VNR in an ATM Network (Logical View)  ...................................... 1-4

Figure 1-3.

SVC/PVC Signaling Protocol Stack  .................................................................... 1-9

Figure 1-4.

Model 5000BH ATM/Router Backplane Bus Structure  .....................................1-11

Figure 1-5.

Model 5782 VNR Module  ................................................................................. 1-14

Figure 1-6.

LED Display on the Model 5782 VNR  ............................................................. 1-15

Figure 1-7.

Reset Button on the Model 5782 VNR  .............................................................. 1-16

Figure 2-1.

Model 5000BH Chassis Backplanes .................................................................... 2-3

Figure 2-2.

Inserting the Flash Memory Card into the Model 5782 VNR  ............................. 2-5

Figure 2-3.

Removing a Filler Panel  ...................................................................................... 2-6

Figure 2-4.

Inserter/Extractor Levers in the Vertical Position  ................................................ 2-7

Figure 2-5.

Seating the Module  .............................................................................................. 2-8

Figure 2-6.

Airflow Module Orientation  ................................................................................ 2-9

Figure 2-7.

Replacing the Filler Panel .................................................................................. 2-10

Figure 2-8.

Removing a Module ........................................................................................... 2-12

Figure 2-9.

Removing the Flash Memory Card .................................................................... 2-13

Figure 2-10.

Flash Memory Card Read/Write Protect Switch ................................................ 2-14

Figure 3-1.

Slot Selection Menu for the Model 5000BH Chassis  .......................................... 3-4

Figure 3-2.

Service Port Main Menu  ...................................................................................... 3-5

Figure 3-3.

Sample NVFS dinfo Display  ............................................................................... 3-7

Figure 3-4.

Sample Installation Files ...................................................................................... 3-7

Figure 3-5.

Beginning of the Quick-Start Installation  ...........................................................3-11

Figure 3-6.

Summary Information for a Quick-Start Installation ......................................... 3-12

Figure B-1.

LED Display for the Model 5782 VNR ............................................................... B-1

Figure C-1.

Network Example for the Quick-Start ATM Worksheet ...................................... C-2

Summary of Contents for 5782











































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands