manualshive.com logo in svg

Bay Networks 5782, User Manual

Share
Download
Bay Networks 5782 User Manual Download Page 64

Using the Model 5782 ATM Virtual Network Router

3-10

119557-A Rev. 00

Running the Quick-Start Installation Script

After booting the router with the ti_5000.cfg file and establishing a new 
Technician Interface session, you are ready to run the Quick-Start installation 
script (install.bat). The router module should already be connected to the 
appropriate Model 5000 chassis slot (see the procedure in 

“Starting the Technician 

Interface

).

Before you run the script, review the list of Quick-Start commands in 

Table 3-4

.

To run the Quick-Start script:

1.

Start the script by entering the following command:

run install.bat

The Quick-Start installation script begins and displays the startup banner and 
the introduction (

Figure 3-5

).

Note: 

Use install.bat once to configure the initial interface. To configure other 

interfaces, use Site Manager to create new configurations.

Table 3-4.

Technician Interface Quick-Start Commands

Task

Key 
Sequence

Details

Accept a default value.

Press [Enter]

Your terminal displays default values 

in brackets, for example, 

ATMSR_XXXXXXX

.

Repeat a step (for example, if 
you make a mistake).

Press 
[Cc 

When prompted 

Terminate 

script y/n?

, type 

n

. The script 

returns to the beginning of the step 
so that you can reenter the 
information.

Exit the Quick-Start installation 
script.

Press 
[Cc 

When prompted 

Terminate 

script y/n?

, type 

y

. The 

Quick-Start script terminates and 
returns to the Technician Interface 
prompt. Reboot the router using the 
ti_5000.cfg file before rerunning the 
Quick-Start installation script.

Summary of Contents for 5782











































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands