manualshive.com logo in svg

Bay Networks 5782, User Manual

Share
Download
Bay Networks 5782 User Manual Download Page 78

Using the Model 5782 ATM Virtual Network Router

C-4

119557-A Rev. 00

Table C-1.

Quick-Start ATM Worksheet

Requested Information

Example

Your Information

ATM Physical Link Information

Slot number of the net module

4 (ATM_VNR_BH)

Connector number [1]: 

1 (ATM1)

Choosing a Service Record Type

Enter ATM Service Record Type [1]:
1. ATM PVC
2. ATM LAN Emulation
3. ATM Logical IP Subnet

Continue with the information for your service record 
type.

1 (ATM PVC)

PVC Service Record Type

Enter encapsulation type [1]:
1. LLC/SNAP (RFC 1483)
2. NLPID (RFC 1490)

2 (NLPID (RFC 1490))

For VPI, enter a number from 0 to 255.

The VPI (virtual path identifier) number of the initial PVC 
identifies the virtual path of the PVC. The VPI is part of 
the cell header. The header can contain a maximum of 8 
VPI bits. This bit range allows for path identifiers from 0 
through 255.

0

For VCI, the valid range of a Model 5782 VNR installed 
in a 5000BH chassis is from 130 to 2047. 
The VCI (virtual channel identifier) number of the initial 
PVC identifies the virtual channel of the PVC. The VCI is 
part of the cell header. The header can contain a 
maximum of 16 VCI bits. 

200

Enter circuit name:
(The script recommends a default name.)

ATMSR_1404101.3

(continued)

Summary of Contents for 5782











































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands