Bavarian RC Messerschmitt Me-410 Build Instructions Download Page 7 | Manualshive

Page: 7 / 58

Bavarian RC Messerschmitt Me-410 Build Instructions Download Page 7

Bavarian RC Messerschmitt Me-410

© 2021 BAVARIAN RC. Plans and instructions provided free of charge. Copies allowed for personal use only. Not for commercial use.

-

7 -

Version Beta 1.0

Horizontal Stabilizer

-

Take the horizontal stabilizer and run BBQ skewer along the score cut. Make the cavity wide
enough to be able to insert a BBQ skewer without pressure.

-

Apply hot glue to the cavity for the BBQ skewer and insert the BBQ skewer. Press the
horizontal stabilizer flat on the table and hold it until the glue has fully cooled down.

-

Remove the foam at the leading edge.

-

Run a BBQ skewer along the leading edge

-

Take 2 BBQ skewers and glue them to the leading edge of the horizontal stabilizer.

-

Apply hot glue to the inside of the paper and wrap it around the leading edge.

-

Fold the elevators to the upper side and cut off the little pointed part in the middle.

-

Cut a single bevel on both elevators and reinforce the hinge line with hot glue.

-

Run a BBQ skewer along the score cuts for the control horn and the U-shape steel wire.

«
...
5
6
7
8
9
...
»

Summary of Contents for Messerschmitt Me-410



























































Reviews:

No comments