Bavarian RC Messerschmitt Me-410 Build Instructions Download Page 4 | Manualshive

Page: 4 / 58

Bavarian RC Messerschmitt Me-410 Build Instructions Download Page 4

Bavarian RC Messerschmitt Me-410

© 2021 BAVARIAN RC. Plans and instructions provided free of charge. Copies allowed for personal use only. Not for commercial use.

-

4 -

Version Beta 1.0

-

Now apply hot glue around the circumference of Former H2 (not on H1).

-

Push the Fuselage tail skin further forward to be flush with Former H2 leaving Former H1
free.

-

Make sure that the center mark of the skin top is aligned with the center mark of Former H2.

-

Let the glue cure overnight.

-

Glue together the two Formers F2.

-

Test fit the Formers F2 on the forward edge of the spine (flush with the fwd edge).

-

Apply hot glue to the mating surface of formers F2 and attach them to the spine. Make sure
that the former is perfectly aligned with the fwd edge of the spine and is at a 90 degree angle
towards the spine.

-

Take the Lower deck and mark the position of Formers A2, B and D on the upper side.

-

Remove the foam from the cavities.

-

Apply hot glue to the cavities and make an A Fold.

-

Test fit the lower deck on the fuselage. Make sure the lower deck perfectly fits to the cavity.
in former H1 and formers F2 and is fully in contact with the lower edge of the spine.

«
...
2
3
4
5
6
...
»

Summary of Contents for Messerschmitt Me-410



























































Reviews:

No comments