Bavarian RC Messerschmitt Me-410 Build Instructions Download Page 51 | Manualshive

Page: 51 / 58

Bavarian RC Messerschmitt Me-410 Build Instructions Download Page 51

Bavarian RC Messerschmitt Me-410

© 2021 BAVARIAN RC. Plans and instructions provided free of charge. Copies allowed for personal use only. Not for commercial use.

-

51 -

Version Beta 1.0

-

Remove the foam from the cavities of the Air intake.

-

Remove the paper from the rear wall.

-

Run a BBQ skewer along the score line between the center part and the rear wall.

-

Apply glue to the cavity on one side a make a B-fold.

-

Repeat this step for the other side.

-

Apply glue to the fwd cavity and make an A-fold.

-

Bevel the lower edges to fit to the bottom of the nacelle.

-

Test fit the Air intake on the nacelle underside. Make sure that the fwd edge of the Air intake
is aligned with the fwd edge of Nacelle skin 3 and the center mark of the Air intake is
matching the center line of the nacelle.

-

Apply glue to the edges of the Air intake and attach it to the Nacelle underside.

«
...
49
50
51
52
53
...
»

Summary of Contents for Messerschmitt Me-410



























































Reviews:

No comments