Bavarian RC Messerschmitt Me-410 Build Instructions Download Page 17 | Manualshive

Page: 17 / 58

Bavarian RC Messerschmitt Me-410 Build Instructions Download Page 17

Bavarian RC Messerschmitt Me-410

© 2021 BAVARIAN RC. Plans and instructions provided free of charge. Copies allowed for personal use only. Not for commercial use.

-

17 -

Version Beta 1.0

-

The build of the nose will be a bit tricky, take your time and slowly adjust the skins to make
them fit.

-

Glue together Former A1 and the two Nose formers.

-

Make a bevel cut around Former A1.

-

Remove the paper from the back of Nose skin 1 and carefully mold it to fit around the Nose
formers.

-

Test fit the Nose skin 1. Make sure that the bottom edge (with the triangle parts) is
overlapping enough (but not more) to be able to properly trim it to be flush with the rear
face of Former A1.

-

Then glue Nose skin 1 to the Nose formers from the nose tip along the upper edge.

Note: A prototype version of Nose skin 1 (without triangle part) is shown in these pictures

-

Trim off the foam (without cutting the paper on the back) on the upper edge.

«
...
15
16
17
18
19
...
»

Summary of Contents for Messerschmitt Me-410



























































Reviews:

No comments