manualshive.com logo in svg

Bavarian RC Messerschmitt Me-410, Build Instructions, Page: 1 / 58

Share
Download
Bavarian RC Messerschmitt Me-410 Build Instructions Download Page 1

Bavarian RC Messerschmitt Me-410 

 

 

 

© 2021 BAVARIAN RC. Plans and instructions provided free of charge. Copies allowed for personal use only. Not for commercial use. 

 

-

 

 1 - 

Version Beta 1.0

 

Bavarian RC Messerschmitt Me-410 – Build Instructions 

 
Note: Some pictures were taken from different prototypes. There might be evolutions in the plans 
that are not matching the pictures. 
 
Fuselage 
 

-

 

Glue together the 3 layers of the Spine (LH, center, RH) 

 

 

 

 

-

 

Glue together the two Formers H2. 

-

 

Slide the Formers H2 onto the spine and glue them in place. Make sure they are at a 90 
degree angle towards the spine. 

 

 

 

-

 

Glue Former H1 in front of Formers H2 and make sure to remove any glue from the 
rectangular cut-out. Punch through the hole for the push rod sleeve. 

 

 

 

 

-

 

Glue together the two Frames L for the LH side and the two Frames L for the RH side 

-

 

Glue the Push rod support and Frames L (LH and RH) to the Spine. 

 

 

Summary of Contents for Messerschmitt Me-410



























































Reviews:

No comments