Baudouin 12M26 Series Operation And Maintenance Manual Download Page 66

Page: 66 / 83

O&M Manual for PowerKit

M26 Series Diesel Engine

6.3 Fuel Recommendation

IMPORTANT:

Improper fuel additive usage may cause damage to fuel injection equipment of diesel engines.



Quality Grade

Use commercially available diesel fuel with less than 0.35% Sulphur content. If the sulfur

content is higher than 0.5%, oil change intervals should be halved.

The following fuels can be used on Baudouin engine:

--- European standard EN 590.

--- ASTM D-975 No.1 D

--- BS 2869 Part 1 Class A 1 standard



Winter-grade Fuel

Waxing may occur at low temperature, clog-

ging the fuel system and reducing engine

efficiency. If the ambient temperature is less

than 0

℃，

winter-grade fuel should be used.

At temperature below -20

℃

,kerosene

should be added to the diesel fuel. The rel-

evant percentages are given in the diagram

below. In most cases, adequate resistance

to cold can be obtained by adding a flow

improver.

Summary of Contents for 12M26 Series




















































































Search results

Summary of Contents for 12M26 Series

Reviews:

Related manuals for 12M26 Series

Brands by name

Popular brands

Baudouin 12M26 Series, Operation And Maintenance Manual

Search results

Summary of Contents for 12M26 Series

Reviews:

Related manuals for 12M26 Series

Brands by name

Popular brands