Baudouin 12M26 Series Operation And Maintenance Manual Download Page 59

Page: 59 / 83

O&M Manual for PowerKit M26 Series Diesel Engine



Clean the radiator and cooling system



Clean the oil cooler(s)



Use steam to clean the oil cooler

core. This removes any remaining

residue from the cleaner. Flush the

fins of the oil cooler core. Remove

any other trapped debris



Wash the oil cooler core with hot,

soapy water. Rinse the oil cooler

core thoroughly with clean water.



Dry the oil cooler core with com-

pressed air. Direct the air in the

reverse direction of the normal

flow.



Check the rocker arm and cross-bar

clearance



Clearance of intake valve is 0.3 ±

0.03 mm and that of exhaust valve

is 0.6 ± 0.03 mm.



Check the battery, battery electrolyte

level, battery charger, battery cables

Summary of Contents for 12M26 Series




















































































Search results

Summary of Contents for 12M26 Series

Reviews:

Related manuals for 12M26 Series

Brands by name

Popular brands

Baudouin 12M26 Series, Operation And Maintenance Manual

Search results

Summary of Contents for 12M26 Series

Reviews:

Related manuals for 12M26 Series

Brands by name

Popular brands